Keg Dispensing Supplies

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the 1/4" Quick Connect Insert, item #05P01-122.

When summer comes around, so do the fruit flies. These little buggers are attracted to the sweet, sweet smell of beer...and who can blame them? But once they smell the sticky syrup that condenses in the mouth of your faucet, they colonize and take over, laying eggs and making your kegerator or draft setup a nightmare! Keep those fruit flies out of your tap with Beer Tap Caps! These little rubber caps, though inconspicuous, can save you from summertime infestations of biblical proportions. Keep these on your faucets when not in use, and you'll drastically reduce fruit fly populations in and around your draft system!

A black plastic picnic faucet comes in handy in a pinch! Affectionately referred to as a cobra tap, this is a fairly simple dispensing mechanism. When the lever is pressed, the rubber gate is lifted, allowing beer to flow. These picnic faucets come apart easily for cleaning, and feature a barbed end that can fit on standard beer line. Make your own or keep one on hand in case the unthinkable happens!

German beer lovers rejoice! This "A" style German slider keg coupler, also known as a tap, is just what you need to get beer flowing from German kegs! This coupler is like no other, with a cupped mount that slides onto the keg and locks in place when engaged. This is the most widely used keg coupler in Germany, and while it will not work with all German beer kegs, it does work with most of them, as well as with a few Belgian kegs. Among the breweries that use the "A" coupler are Ayinger, Achouffe, Bitburger, Franziskaner, Hacker-Pschorr, Hoegaarden, Paulaner, Spaten, and Warsteiner. This coupler comes with the gas side connections, but does not include the liquid side connections which consist of a 3/16" liquid tailpiece, a beer nut and a neoprene washer.

Superflush Tap & Line Cleaner is an safe, easy-to-use, economical and biodegradable line cleaner perfect for use on kegerators and draft dispensing systems. Simply mix 2-3 oz. with 1 gallon water as per the instructions and pump through lines. Allow to sit in lines for a few minutes, then flush clean with water. A solution made at the same rate may be used to clean faucet and coupler parts as well. Sold in a 32 oz bottle, Superflush can help you keep your lines pristine, pouring perfect beer every time!

A swivel nut set with a barb for your liquid side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 1/4" barb. This swivel nut set is perfect for use with standard 3/16" ID liquid tubing, thin or thick-walled. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

Is your tap handle too short? Not visible or prominently displayed, like you would like? Look no further than this chrome extension to solve your tap handle woes! This 1-inch chrome extension is placed between your faucet and tap handle to extend it outwards. Simple to use and effective, get the right length for your tap handle today!

Bevlex tubing is a high quality thick-walled tubing. This 3/16" tubing works well for beer line, as it is the standard inner diameter for most serving systems. While the thinner walled tubing may also be used, this thick-walled tubing is recommended for permanent installations, such as on a kegerator or keezer dispensing system. It is also recommended when a thicker wall would come in useful. It is more durable and can withstand more pressure than the thinner-walled version.

Inner Diameter: 3/16 in.
Outer Diameter: 7/16 in.

The name Perlick has been in the beverage industry for a long time, and has always been associated with high quality draft equipment. The 630SS is no exception. This faucet is forward-sealing so there is less chance of bacterial and yeast activity. A high-quality forward sealing faucet such as this will need to be cleaned less frequently than an inferior back-sealing standard faucet. Being all-stainless, this Perlick faucet is built to last! Staying strong long after other metals begin to degrade, a stainless steel Perlick faucet is something of a long-term investment, but well worth the price!

Do you often carbonate and serve beer at the same time? If so, or if you would like to be able to do both at different pressures, a secondary regulator is perfect for you! Your primary CO2 regulator attaches to your CO2 tank and allows one output pressure. However, a secondary regulator hooks up inline and allows you to regulate to another keg at a lower pressure. This allows you to carbonate one keg at a higher pressure while serving beer from another at a lower pressure! This Taprite secondary regulator is made to the same high standards as all Taprite equipment, with a high quality diaphragm that keeps regulating long after lesser regulators give up the ghost. Regulate at multiple pressures with a secondary regulator from Taprite!

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.

Don't give up on that old Perlick faucet, repair it! The Perlick repair kit was made for repairing the internals of a 425 series Perlick faucet, and comes with a stainless steel lever, a stainles steel plunger, and a chrome collar. These should be all the internal parts needed to repair a 425 Perlick. Breathe new life into that faucet with a repair kit!

Standard faucets are just that...standard faucets for pouring beer! They come standard with a number of kegerators and dispensing setups, and can be found on jockey boxes, homemade beer fridges and keezers, just about anywhere you find beer! Economical, they are easy to take apart and clean, with just a few moving parts that can easily be replaced if needed. These make great replacement faucets for damaged faucets on existing setups, or work well on new installations as well! These can be put on the end of a shank for a new installation.

This Bevlex tubing measures 1/2" inner diameter, making it perfect for use with a 1/2" racking cane or large auto-siphon. The thicker walling is kink-resistant, and is perfect for more rigorous applications. Some people have been known to use this tubing for racking using a vacuum pump, and others just prefer it to thin-walled tubing because of its durability. Whatever you use it for, we've got it here for you!

Inner Diameter: 1/2 in.
Outer Diameter: 3/4 in.

This is a black plastic flange, the type that comes with standard beer shanks. It makes your custom kegerator look nice and professional, covering up drilled holes and providing a nice background for your beer faucet. If yours are damaged, replace them with this flange!

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These medium Oetiker clamps are often used on 3/16" thick-walled tubing that is used in some liquid applications and in draft systems. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

Everyone with a draft system should own a spanner wrench! This little curved tool hooks into the holes on the faucet coupler to loosen or tighten your faucet as needed. Even if you bought a draft system preassembled, you will still want to take the faucet off and clean it periodically to ensure the cleanest pour possible.

Smooth and straight! This flange for the inside of your beer tower is made of black plastic. It is curved on one side to fit the curvature of the beer tower. The lock nut can be tightened up against the flange in order that everything is straight on your kegerator! These flanges sometimes get damaged or lost. This flange is the perfect replacement for most flanges on standard sized beer towers.

A swivel nut set with a barb for your gas side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 5/16" barb that can be used with standard 5/16" ID gas tubing. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

This 3/16" tailpiece works with standard 3/16" ID liquid side tubing in a range of liquid dispensing applications. Most commonly, this tailpiece is used with a beer nut and a neoprene beer washer on the end of a shank as part of a faucet draft system. However, they are also used on sanke couplers for the liquid dispensing side. They can come in quite handy when replacing preinstalled liquid side connections in kegerators.

Get that coupler into your kegerator! Some kegerators don't have a lot of clearance space, and a standard keg coupler won't fit on top of the keg. The solution to this problem? A low-profile sanke coupler! This coupler measures a mere 3.25", taking up less space above your keg than normal couplers. It has a unique design by which the engaging mechanism twists down the body and engages into the keg. Above the engaging body, the CO2 comes in the sideways barb, and liquid flows out sideways as well. Perfect for kegerator setup without a lot of vertical room! This coupler comes with an integrated gas barb. Not included is a 3/16" liquid tailpiece, beer nut and neoprene washer.