Keg Dispensing Supplies

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the 1/4" Quick Connect Insert, item #05P01-122.

This 5/16" tailpiece works with standard 5/16" ID CO2 tubing. Most often, these are found on the CO2 side of sanke couplers. Used in conjunction with a beer nut and a neoprene beer washer, these tailpieces can create a tight seal for CO2. Useful as a replacement on kegerator setups, make sure you have one on hand in your draft emergency kit!

Make your dream draft system at home! Our standard faucet assembly includes everything you will need to put a faucet on an old fridge, or on the collar of a chest freezer.

This standard assembly includes:
Standard chrome-plated faucet
Faucet knob
Chrome-plated 4 1/8 in. shank with 3/16 in. bore
Beer nut, neoprene washer and 3/16 in. tailpiece

Simply drill your hole, install your assembly, and hook your liquid line into the 3/16 in. tailpiece in the back of the assembly, and you'll be pouring draft beer in no time! Perfect for refrigerator or chest freezer conversions. Get a few and have multiple beers on at once!

The secret weapon for keeping a clean brewery! A double ended brush can come in handy for cleaning all those hard-to-reach places, not only in your dispensing system, but also in your brewing equipment. The two ends have two different sizes brushes, which come in handy in cleaning faucet parts, keg posts, dip tubes, racking arms, ball valves, bottle fillers...the list goes on! Keep every nook and cranny of your brewing equipment clean with one of these. Highly recommended to anyone who owns a keg or a permanent dispensing setup.

A swivel nut set with a barb for your gas side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 5/16" barb that can be used with standard 5/16" ID gas tubing. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

Always have a tap when the party demands one! This economy twist sanke pump tap is a classic party-style pump coupler. It features a pump for pressurizing a keg with air, a twist-style coupling mechanism similar to those found on low-profile sanke couplers, and a short black picnic faucet. This is the perfect, economical solution for kegs that are going to be quickly consumed. Instead of paying the liquor store multiple deposits, invest in a pump tap and always be prepared to get the party started!

Make your coonecitons tight! With this grommet, you can create the perfect seal for your liquid tower elbow. This will allow the beer to continue flowing freely for years to come!

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.

This CO2 shutoff with 1/4" MPT threading and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is standard 1/4" MFL threading, which works perfectly with standard swivel nut sets and other 1/4" MFL fittings. If using a swivel nut set, we recommend using a plastic flare fitting as well, in order to create a good seal. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!

A bent tailpiece can come in extremely handy when connecting liquid lines in hard-to-reach places, such as kegerator towers or homemade keezers and kegerators. Not only that, but a 90 degree bend just makes sense in some setups! This tailpiece has a standard 3/16" barb, perfect for liquid line applications. It is often used with a beer nut and a neoprene beer washer for a secure seal.

The "G" type coupler is sometimes known as a Bass keg coupler or tap. This is the style of coupler used on Bass, Boddington's, Anchor, Grolsch, Old Speckled Hen, Innis & Gunn and Watney's kegs, among others. Without this style of coupler, it may be hard to get beer out of kegs from those breweries! This coupler comes with the gas side connections, but does not come with the 3/16" liquid tailpiece, beer nut or neoprene washer needed for the liquid side.

Superflush Tap & Line Cleaner is an safe, easy-to-use, economical and biodegradable line cleaner perfect for use on kegerators and draft dispensing systems. Simply mix 2-3 oz. with 1 gallon water as per the instructions and pump through lines. Allow to sit in lines for a few minutes, then flush clean with water. A solution made at the same rate may be used to clean faucet and coupler parts as well. Sold in a 32 oz bottle, Superflush can help you keep your lines pristine, pouring perfect beer every time!

Simply put, this is a check valve ball. It works with standard NADS American "D" sanke couplers, as well as other sanke couplers that use the same ball. This helps to keep your beer in "check" by blocking backflow of liquid back through the valve. In some instances, people will lose the ball while cleaning the coupler. If this happens, never fear! We've got a replacement for you so you can keep that beer safely flowing!

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 3/8" straight barb to hook up to 3/8" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the Male 3/8" In-line Hose Barb, item #05P01-123.

If the diaphragm goes out on your Taprite regulator goes out, there's nothing left to do but get a whole new regulator, right? Not anymore! Great Fermentations brings you this regulator repair kit that comes with the parts and instructions you need to fix your regulator. Much cheaper than buying a whole new regulator, give this kit a try!

Replace your missing or damaged coupling nut with one of these brass replacements from Great Fermentations! These also work well with a faucet adapter (item #17C13-100). Put one of these on the faucet adapter, add a faucet and a liquid disconnect on the other end, and you have yourself a faucet assembly ready to put on a cornelies keg!

Have some extra tubing on hand for all your kegging needs! 5/16" inner diameter tubing is the standard tubing used in kegging and carbonation systems in the U.S. The Bevlex tubing we carry is thick-walled for extra protection and security when carbonating. This can be used on all standard CO2 connections in your draft system.

Inner Diameter: 5/16 in.
Outer Diameter: 9/16 in.

From Taprite comes this "S" style keg coupler, also known as a tap. This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. The "S" style coupler is a common European style coupler used by many leading breweries in Europe, including Stella Artois, Heineken, Beck's, Amstel, Newcastle, Pilsner Urquell, Lindeman's, and Huyghe, makers of Delirium Tremens. It is similar to a North American "D" style coupler, but runs about a 1/4" deeper into the keg. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

Do you want to serve perfect pints of nitrogenated beers every time? The cascading nitrogen bubbles coming from a classic Irish stout come to mind, as do other styles, such as IPAs, imperial red ales, and classic British pub ales that are sometimes served on nitrogen. To pour these beers perfectly, you need a stout faucet...and we've got just the one for you! This stout faucet is the same classic faucet design that Guinness is poured from at your favorite traditional Irish and British pubs. In addition, many bars and restaurants use this style for pouring any nitrogenated beers! Featuring a stainless steel straight nozzle with a stainless steel restrictor plate that forces the beer to come out creamy and smooth, the design allows for pulling forward to pour beer and pulling back to give a creamy froth to the beer. Use with beer gas to achieve that perfect pour!

This faucet features a chrome plated body, with a stainless steel restrictor disk and nozzle.

This Bevlex tubing measures 1/2" inner diameter, making it perfect for use with a 1/2" racking cane or large auto-siphon. The thicker walling is kink-resistant, and is perfect for more rigorous applications. Some people have been known to use this tubing for racking using a vacuum pump, and others just prefer it to thin-walled tubing because of its durability. Whatever you use it for, we've got it here for you!

Inner Diameter: 1/2 in.
Outer Diameter: 3/4 in.

Want to pour the perfect stout or nitro beer every time? With the stout faucet assembly, you'll be able to add a stout faucet to your kegerator that pours a rich, creamy head on all nitrogenated or beer gas beers. Perfect for Guinness or Guinness clone beers, but can be used with a range of beer gas beers or beers on nitro, such as the nitrogenated IPAs and Imperial Red Ales that have become popular as of late.

Assembly Includes the Following:
Stout faucet (Chrome plated body with a stainless spout and stainless restrictor plate).
Faucet knob
Chrome-plated 4 1/8 in. shank with 3/16 in. bore
Beer nut, neoprene washer and 3/16 in. tailpiece

Get this assembly, add it to your kegerator or keezer system, and impress all your friends with perfect pours every time!