Keg Dispensing Supplies

From Johnson Controls, a trusted name in temperature control and thermostats, comes this handy external thermostat that can be used to keep your beer at just the right temperature! The unit consists of a probe that goes into your cooling device (refrigerator or freezer), an analog thermostat that ranges between 20 and 80 degrees Fahrenheit, and a power cord with plug outlet for the cooling device. Simply place the probe on the inside of your cooling device, plug your device into the unit, and set your temperature. Done! The unit will interrupt power to the cooling device when the temperature goes too far out of range of the set temperature.

Note: that there is a 3 ½ degree differential between the set point and the actual temperature. However, this range should have minimal effect on the actual beer temperature. Using this control, homebrewers have been able to make excellent lagers all year round, cold crash their beers, and so much more!

Turn your fridge into a kegerator with our kegerator homebrew kegging system! This system comes with all the internal workings of a kegerator system you will need, except the CO2 cylinder.

Included is a high quality Taprite regulator, ball lock gas line assembly, a used 5 gallon cornelius keg, a ball lock liquid disconnect with swivel nut set, 6 feet of 3/16" ID Bevlex thick-walled liquid tubing, and a full shank assembly that includes a standard beer faucet, faucet knob, 4" shank, 1/4" tailpiece, beer nut and neoprene washer. Make the draft system you have always wanted with this kegerator kegging system!

All you'll need in addition to this kit to make the ultimate kegerator, is a full CO2 tank. For local customers we sell full tanks at all of our retail locations!

These check valves are the perfect solution to backflow issues that you may be having. They go on the gas side of a ball or pin lock gas system. They have an integrated back check valve that helps prevent flow from reversing, and fit on the 1/4" MFL fitting found on most standard ball or pin lock disconnects. Keep your gas lines clean with these as a preventative measure.

You can never have too many disconnects! For all your ball lock draft needs, Great Fermentations offers you these gas ball lock disconnects. Easy to take apart and clean, these are used with 5/16" ID Bevlex tubing on manifolds and splitters to carbonate multiple kegs at once. These disconnects have a 1/4" MFL connection, which is perfect for attaching a swivel nut set for myriad applications. They have a plastic end on the male flare fitting so you don't have to use a plastic flare fitting washer when connecting them to metal. Make sure you have enough on hand for all the kegging and draft projects your mind can come up with!

This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. This "D" style coupler is the standard coupler used by virtually all American and Canadian breweries, and as such, this is the most convenient keg coupler to own in North America. One of these allows you to tap almost any keg from any American or Canadian breweries. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

Long and narrow, the dip tube brush was made specifically for cleaning out keg dip tubes. Being long and narrow themselves, dip tubes can be tricky to clean properly without the right tool. Cleaning out a dip tube with a dip tube brush ensures that you scrub the whole inner surface of the dip tube, where bacteria and beer stone can easily hide. These brushes are also good for cleaning sight glasses and other narrow brewing equipment. Another brush highly recommended to anyone who owns a keg!

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 4" shank is a standard size (actual measurement is 4 1/8") and works on most applications. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

This is a male compression nut for beer towers. It goes in the end of a shank and accomodates a liquid tower elbow to get the beer flowing! You may also need a tower grommet to help create a good seal. With these, you should have the beer flowing from your tower in no time!

This is a replacement washer for the lever on the old 425 series Perlick faucets. If your old faucet is in need of some new washers, we've got you covered! These are the perfect replacement for old, disused Perlick 425 series faucets.

This replacement o-ring fits on Perlick faucets. It is the o-ring that seals the lever component of the faucet. Integral in the proper functioning of these Perlick faucets, it is never a bad idea to have an extra on hand!

Party Pig Valve Assem with gasket

Chrome replacement collar for the Perlick Perl faucet.

3" Chrome Dual Tap Tower

Three is better than one! This 3" beer tower extension not only extends your tower, but comes with two shanks for adding two more faucets to your tower setup. With the existing fauet, this means that you can have up to three beer faucets on your setup! Perfect for going big with your existing 3" beer tower, get your extension today!

This is the ball needed for the Guiness "U" coupler which prevents backflow. As opposed to the check valve ball on a standard keg, the ball found in the Guiness coupler is slightly larger. Make sure you have the right one for your coupler!

Turn your fridge into a kegerator with our kegerator homebrew kegging system! This system comes with all the internal workings of a kegerator system you will need, except the CO2 cylinder.

Included is a high quality Taprite regulator, ball lock gas line assembly, a brand new 5 gallon cornelius keg, a ball lock liquid disconnect with swivel nut set, 6 feet of 3/16" ID Bevlex thick-walled liquid tubing, and a full shank assembly that includes a standard beer faucet, faucet knob, 4" shank, 1/4" tailpiece, beer nut and neoprene washer. Make the draft system you have always wanted with this kegerator kegging system, complete with a brand spankin' new keg!

All you'll need in addition to this kit to make the ultimate kegerator, is a full CO2 tank. For local customers we sell full tanks at all of our retail locations!

Have you ever damaged a gauge on your CO2 regulator? We've got the replacements you need! This is a left-hand threaded replacement tank pressure gauge for your CO2 regulator. These come standard on dual gauge regulators, and this one works with regulators that take a left-hand threaded gauge.

Want to make your own kegerator? Have a tower that you need replaced? Great Fermentations offers these 3" beer towers for all your tower needs! This model is a standard 3" model, which works well as a replacement on kegerators that have the same sized tower. It has a single beer faucet attached to the tower. If you are making your own kegerator, you can affix this to the top of a dorm fridge or other small refridgerator. Just like that, you've got yourself a kegerator! The sleek chrome finish looks nice as your pour the perfect beer from the tower. Cheers!

This is a replacement black lever washer for standard faucets. It goes on top of the white faucet shaft washer on the faucet lever of a standard faucet. Washers wear out over time, and used equipment that has not been properly maintained may need new washers. If this is the case, Great Fermentations has replacements for you!

Chrome Bonnet for Perlick Forward Faucet

Need new o-rings for the inside of your stout faucet? Look no further! Great Fermentations have these o-rings available to you so that you can keep those creamy beers flowing! These o-rings fit in the body of the faucet above the nozzle and keep everything tight and secure. Have a few on hand so you'll always be prepared for the inevitable!